The order

Alarm name

note

1

Overspeed warning

When the speed of the generator controller detected more than one set of overspeed warning threshold value, the controller issued a warning signal.

2

Owe speed warning

When the speed of the generator controller detected is less than the owe speed warning threshold value set, the controller issued a warning signal.

3

Speed warning signal loss

When the speed of the controller to detect generator set equal to zero, and the type choosing warning, the speed signal loss controller issued a warning signal.

4

Power frequency warnings

As the frequency of the generator controller detected more than one set of frequency warning threshold value, the controller issued a warning signal.

5

Frequency power owe warning

When the controller detected the frequency of the generator set is less than the owe frequency warning threshold set, the controller issued a warning signal.

6

Generating overvoltage warning

When controller detected generator voltage is greater than the overvoltage warning threshold value set, the controller issued a warning signal.

7

Power generation under-voltage warning

When the controller detected the generator voltage is less than the under-voltage warning threshold value set, the controller issued a warning signal.

8

Power flow warning

When the controller detected generating set is greater than the current set of over-current value, cross flow type choice of warning, the controller issued a warning signal.

9

Unbalanced power current warning

When the generator of an imbalance between the three phase load current and greater than the set value only a warning

10

Stop failure warning

When the generator set to a complete stop after the delay, if the engine did not stop, the controller issued a warning signal.

11

Charging failure warning

When the controller detected charge electromechanical voltage value of the generating set is less than the threshold set, warning alarm controller.

12

Battery over-voltage warning

When controller detected generating set of the battery voltage is greater than the threshold set, warning alarm controller.

13

Battery under voltage warning

When the controller detected generating set of the battery voltage is less than the threshold set, warning alarm controller.

14

Maintain 1 time to warning

When maintaining the countdown to 1, and the type choosing warning, the maintenance time to controller issued a warning signal.

15

Maintain 2 time to warning

When maintaining the countdown to 2, and the maintenance time to action type choose warning, the controller issued a warning signal.

16

Maintain 3 time to warning

When maintenance the countdown 3, and the maintenance time to action type choose warning, the controller issued a warning signal.

17

Reverse power warning

When the controller detected the inverse power generating set value (negative) power than set threshold, and the type choosing warning, the reverse power controller issued a warning signal.

18

Overpower warning

When the controller detected generator power to power (is) a value greater than the setting threshold, and overpower movement type choosing warning, the controller issued a warning signal.

19

The power lacks a warning

When the controller detects power generation phase, the controller issued a warning signal.

20

Reverse phase sequence warning to generate electricity

When power controller detected inverse phase sequence, the controller issued a warning signal.

21

Power switch failure

When the controller power switching instruction starting test after closing state input is valid, if have not detected within the preset switching delay effective, closing failure warnings.This warning will not automatically eliminated.(can be eliminated according to mute)

22

Mains switch failure

When the controller mains switch instructions starting test after closing state input is valid, if have not detected within the preset switching delay effective, closing failure warnings.This warning will not automatically eliminated.(can be eliminated according to mute)

23

Power points brake failure

When the controller power points after the brake starting test switching state input is valid, if within the preset points gate delay had been detected at effective, break-brake failure warnings.This warning will not automatically eliminated.(can be eliminated according to mute)

24

Grid points brake failure

When the controller state grid points after instruction starting test perform the input is valid, if within the preset points gate delay had been detected at effective, break-brake failure warnings.This warning will not automatically eliminated.(can be eliminated according to mute)

25

Temperature sensor open warning

When open circuit controller to detect sensor, and the type choosing warning, the open circuit controller issued a warning signal.

26

High temperature warning

When the temperature of the controller to detect value is greater than the set of high temperature warning value, the controller issued a warning signal.

27

Low temperature warning

When the temperature of the controller to detect value is less than set warning value, low temperature controller issued a warning signal.

28

Oil pressure sensor open warning

When open circuit controller to detect sensor, and the type choosing warning, the open circuit controller issued a warning signal.

29

Low oil pressure warning

When the controller to detect oil pressure value is less than the oil pressure warning numeric set, warning alarm controller.

30

Liquid level sensor open warning

When open circuit controller to detect sensor, and the type choosing warning, the open circuit controller issued a warning signal.

31

Low level warning

When the controller detection of liquid level value less than the level of set warning value, the controller issued a warning alarm signal.

32

1 open warning programmable sensors

When open circuit controller to detect sensor 1, and the open type choose warning, the controller issued a warning signal.

33

High programmable sensors 1 warning

When the controller detection sensor 1 numerical value is greater than the limit set by the warning value, the controller issued a warning signal.

34

A programmable low warning sensor 1

When the controller detection sensor 1 value less than the lower limit of set warning value, the controller issued a warning signal.

35

2 open warning programmable sensors

When the controller detected sensor 2 open circuit, and the type choosing warning, the open circuit controller issued a warning signal.

36

2 high warning programmable sensors

When the controller detection sensor 2 value is greater than the limit set by the warning value, the controller issued a warning signal.

37

2 low warning programmable sensors

When the controller detection sensor 2 value is less than the lower limit of set warning value, the controller issued a warning signal.

38

Input port 1 warning

When the switch input port and 1 configuration is warning, and effective, the controller corresponding warning signal input port.

39

Input port 2 warning

When the switch input port 2 configuration is warning, and effective, the controller corresponding warning signal input port.

40

Input port 3 warning

When the switch input port and 3 configuration is warning, and effective, the controller corresponding warning signal input port.

41

Input port 4 warning

When the switch input port and four configuration is warning, and effective, the controller corresponding warning signal input port.

42

Input port 5 warning

When the switch input port and 5 configuration is warning, and effective, the controller corresponding warning signal input port.

43

Input port 6 warning

When the switch input port and 6 configuration is warning, and effective, the controller corresponding warning signal input port.

44

Input port 7 warning

When the switch input port and 7 configuration is warning, and effective, the controller corresponding warning signal input port.

45

Input port 8 warning

When the switch input port and 8 configuration is warning, and effective, the controller corresponding warning signal input port.

46

DTU communication failure warning

When setting and DTU binding, controller and DTU communication failure is display instructions.